Since we pre-fill the cached `keyMap` with the value of `DefaultLayer`, there is
no need to check that layer again, looking for a non-transparent key. Whatever
is there, will be used anyway.
This way we save a cycle for keys that are transparent everywhere but the
default layer.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
We fill the cached `keyMap` with the value of `DefaultLayer`, so if that is the
only layer active, then we can bail out early.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of going through all the active layers each time we are looking for a
key, whenever we switch layers, compute the effective keymap, and store the
indexes. This makes the lookup a considerably faster operation, and lookups
happen far more often than layer switching.
This comes at a cost of ROWS*COLS amount of memory, and a bit of code, but on
the flip side, the lookup operation is now O(1), which is a very nice property
to have, if you want responsiveness. Changing layers is marginally slower,
however, but even with 32 active layers, doing the computation once, instead of
potentially many dozens of time, is still worth it.
We could further reduce the memory requirements if we stored more columns per
byte, but that's for a future optimization.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
The build-all command needs a clean(-ish) slate, and must re-set the build-dir,
otherwise a successful build of a previous plugin will remove it. As a
workaround, re-launch the builder in this case.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of always iterating through all layers, which slows us down
considerably, keep track of the highest active one, and start from there.
This has a VERY noticeable impact on the speed at which we finish a scan cycle.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Momentary layer switchers were broken, because they had the flags/keyCode parts
swapped. Apparently, I missed these when swapping the rest.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
The function is broken, and does not belong here in the first place. It was a
remnant of how Akela was set up, but makes no sense in general.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
It had the COLS & ROWS defines, which are hardware-specific, and were moved to
the hardware lib.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Moved all of the hardware-specific code to a separate library. As such, use the
special `KEYBOARDIO_HARDWARE_H` define to include the appropriate header, as set
by the board's `boards.txt`.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of just switching to a layer, make it a macro. The macro will toggle the
layer and the LED effect.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
All of the plugins have been updated, there is no need to keep the deprecated
functions around anymore.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
When toggling a layer, the same keycode should toggle the layer off, too.
Without this, toggling layers won't work at all, because the target layer will
never be turned off.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Turn the `event_handler_hook_add` and `loop_hook_add` aliases into real
functions, that emit a deprecation warning during compilation. This makes it a
little bit easier to see what needs to be updated still.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
In most cases, one only wants a single copy of a hook. On the other hand,
plugins that depend on other plugins, may want to make it easier for the
end-user to use the plugin, and call the setup function of the dependent plugins
too. In case the end-user calls the same setup function, we'd end up with hooks
registered multiple times.
To avoid this, protection against double-registration has been introduced. The
new `event_handler_hook_use` and `loop_hook_use` functions will only allow one
copy of the hook. The `event_handler_hook_append` and `loop_hook_append`
functions will, on the other hand, just append the hooks, and not care about
protection.
The `event_handler_hook_add` and `loop_hook_add` functions are gone, but for the
time being, they are aliases to the `_use` functions, until all plugins have
been updated, and the aliases can be removed.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Moves the LED control code, along with the built-in effects into the
Keyboardio-LEDControl plugin.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
I forgot to update the `LCTRL`, `LALT`, etc macros, and they still assumed the
previous order. This little patch fixes that.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Jesse Vincent
Gergely Nagy
Jesse Vincent