Kaleidoscope/ArduinoKeyboard.ino

// Do not remove the include below
#include "ArduinoKeyboard.h"
// Copyright 2013 Jesse Vincent <jesse@fsck.com>
// All Rights Reserved. (To be licensed under an opensource license
// before the release of the keyboard.io model 01
#define DEBUG_SERIAL false

/**
 *  TODO:
TEST
TEST2
#left IO Expander found at 0x00

    add mouse inertia
    add series-of-character macros
    add series of keystroke macros
    use a lower-level USB API

*/
#include "ArduinoKeyboard.h"
#include <EEPROM.h>  // Don't need this for CLI compilation, but do need it in the IDE
#include "digitalWriteFast.h"
#include <Wire.h>
#include "sx1509_library.h"



const byte LEFT_SX1509_ADDRESS = 0x70;  // SX1509 I2C address (10)
const byte RIGHT_SX1509_ADDRESS = 0x71;  // SX1509 I2C address (11)
sx1509Class leftsx1509(LEFT_SX1509_ADDRESS);
sx1509Class rightsx1509(RIGHT_SX1509_ADDRESS);

int right_initted = 0;
int left_initted = 0;

#define TS(X) //Serial.print(micros() );Serial.print("\t");Serial.println(X);


void setup_matrix()
{
  reset_key_report();
  //blank out the matrix.
  for (byte col = 0; col < COLS; col++) {
    for (byte row = 0; row < ROWS; row++) {
      matrixState[row][col] = 0;
    }
  }
}


void set_keymap(Key keymapEntry, byte matrixStateEntry) {
  if (keymapEntry.flags & SWITCH_TO_KEYMAP) {
    // this logic sucks. there is a better way TODO this
    if (! (keymapEntry.flags ^ ( MOMENTARY | SWITCH_TO_KEYMAP))) {
      if (key_is_pressed(matrixStateEntry)) {
        if ( keymapEntry.rawKey == KEYMAP_NEXT) {
          active_keymap++;
        } else if ( keymapEntry.rawKey == KEYMAP_PREVIOUS) {
          active_keymap--;
        } else {
          active_keymap = keymapEntry.rawKey;
        }
      }
    } else if (! (keymapEntry.flags ^ (  SWITCH_TO_KEYMAP))) {
      // switch keymap and stay there
      if (key_toggled_on(matrixStateEntry)) {
        active_keymap = primary_keymap = keymapEntry.rawKey;
        save_primary_keymap(primary_keymap);
#ifdef DEBUG_SERIAL
        Serial.print("keymap is now:");
        Serial.print(active_keymap);
#endif
      }
    }
  }
}

void scan_matrix()
{
  x = 0;
  y = 0;
  //scan the Keyboard matrix looking for connections
  for (byte row = 0; row < LEFT_ROWS; row++) {
    TS("Scanning row ")
    if (left_initted) {
      leftsx1509.updatePinState(left_rowpins[row], LOW);
      leftsx1509.sendPinStates();
      leftsx1509.fetchPinStates();
    }
    if (right_initted) {
      rightsx1509.updatePinState(right_rowpins[row], LOW);
      rightsx1509.sendPinStates();
      rightsx1509.fetchPinStates();

    }


    for (byte col = 0; col < LEFT_COLS; col++) {
      TS("Scanning col")
      //If we see an electrical connection on I->J,

      matrixState[row][col] <<= 1;

      matrixState[row][(COLS - 1) - col] <<= 1;

      TS("Reading left pin")
      if (left_initted && leftsx1509.readPrefetchedPin(left_colpins[col])) {
        matrixState[row][col] |= 0;
      } else {
        matrixState[row][col] |= 1;
      }

      TS("Reading right pin")
      if (right_initted && rightsx1509.readPrefetchedPin(right_colpins[col])) {
        matrixState[row][(COLS - 1) - col] |= 0;
      } else {
        matrixState[row][(COLS - 1) - col] |= 1;
      }


      // while we're inspecting the electrical matrix, we look
      // to see if the Key being held is a firmware level
      // metakey, so we can act on it, lest we only discover
      // that we should be looking at a seconary Keymap halfway
      // through the matrix scan


      set_keymap(keymaps[active_keymap][row][col], matrixState[row][col]);
      set_keymap(keymaps[active_keymap][row][(COLS - 1) - col], matrixState[row][(COLS - 1) - col]);
      TS("calling send_key_event")
      send_key_event(row, col);
      if (right_initted)
        send_key_event(row, (COLS - 1) - col);

    }
    TS("clearing output pins")
    if (left_initted)
      leftsx1509.updatePinState(left_rowpins[row], HIGH);
    if (right_initted)
      rightsx1509.updatePinState(right_rowpins[row], HIGH);
  }
  TS("Releasing keys not being pressed")
  release_keys_not_being_pressed();
  TS("Sending key report");
  Keyboard.sendCurrentReport();
  TS("clearing internal key report")
  reset_key_report();
  handle_mouse_movement(x, y);
}

// Command mode
//


void command_reboot_bootloader() {
  Keyboard.println("Rebooting to bootloader");
  Serial.end();


  // Set the magic bits to get a Caterina-based device
  // to reboot into the bootloader and stay there, rather
  // than run move onward
  //
  // These values are the same as those defined in
  // Caterina.c

  uint16_t bootKey = 0x7777;
  uint16_t *const bootKeyPtr = (uint16_t *)0x0800;

  // Stash the magic key
  *bootKeyPtr = bootKey;

  // Set a watchdog timer
  wdt_enable(WDTO_120MS);

  while (1) {} // This infinite loop ensures nothing else
  // happens before the watchdog reboots us
}

void command_plugh() {
  commandMode = !commandMode;
  if (commandMode) {
    Keyboard.println("");
    Keyboard.println("Entering command mode!");

  } else {
    Keyboard.println("Leaving command mode!");
    Keyboard.println("");
  }
}

void setup_command_mode() {
  commandBufferSize = 0;
  commandMode = false;
  commandPromptPrinted = false;
}
boolean command_ends_in_return() {
  if (
    commandBuffer[commandBufferSize - 1] == KEY_ENTER ||
    commandBuffer[commandBufferSize - 1] == KEY_RETURN ) {
    return true;
  } else {
    return false;
  }
}

boolean is_command_buffer(byte* myCommand) {
  if (!command_ends_in_return()) {
    return false;
  }
  int i = 0;
  do {
    if (commandBuffer[i] != myCommand[i]) {
      return false;
    }
  } while (myCommand[++i] != NULL);
  return true;
}


void process_command_buffer() {
  if (!command_ends_in_return()) {
    return;
  }



  // This is the only command we might want to execute when
  // we're not in command mode, as it's the only way to toggle
  // command mode on
  static byte cmd_plugh[] = {KEY_P, KEY_L, KEY_U, KEY_G, KEY_H, NULL};
  if (is_command_buffer(cmd_plugh)) {
    command_plugh();
  }

  // if we've toggled command mode off, get out of here.
  if (!commandMode) {
    commandBufferSize = 0;
    return;
  }

  // Handle all the other commands here
  static byte cmd_reboot_bootloader[] = { KEY_B, KEY_O, KEY_O, KEY_T, KEY_L, KEY_O, KEY_A, KEY_D, KEY_E, KEY_R, NULL};
  static byte cmd_version[] = { KEY_V, KEY_E, KEY_R, KEY_S, KEY_I, KEY_O, KEY_N, NULL};

  if (is_command_buffer(cmd_reboot_bootloader)) {
    command_reboot_bootloader();
  } else if (is_command_buffer(cmd_version)) {
    Keyboard.println("");
    Keyboard.print("This is Keyboardio Firmware ");
    Keyboard.println(VERSION);
  }


  if (!commandPromptPrinted ) {
    Keyboard.print(">>> ");
    commandPromptPrinted = true;
    commandBufferSize = 0;
  }
}


void setup()
{
  wdt_disable();
  Serial.begin(115200);
  //usbMaxPower = 100;
  Keyboard.begin();
  Mouse.begin();
  setup_leds();
  update_leds();
  setup_command_mode();
  setup_matrix();
  setup_pins();
  rightsx1509.fetchPinStates();

  primary_keymap = load_primary_keymap();
}

String myApp;

void loop()
{
  // if(Serial.available()) {
  // myApp = Serial.readString();
  // myApp.trim();
  // }
  TS("A noop takes...")
  TS("about to scan the matrix")
  active_keymap = primary_keymap;
  scan_matrix();
  TS("updating LEDs");
  update_leds();
}





void save_primary_keymap(byte keymap)
{
  EEPROM.write(EEPROM_KEYMAP_LOCATION, keymap);
}

byte load_primary_keymap()
{
  byte keymap =  EEPROM.read(EEPROM_KEYMAP_LOCATION);
  if (keymap >= KEYMAPS ) {
    return 0; // undefined positions get saved as 255
  }
  return keymap;
}




// Debugging Reporting
//

void report_matrix()
{
#ifdef DEBUG_SERIAL
  if (reporting_counter++ % 100 == 0 ) {
    for (byte row = 0; row < ROWS; row++) {
      for (byte col = 0; col < COLS; col++) {
        Serial.print(matrixState[row][col], HEX);
        Serial.print(", ");

      }
      Serial.println("");
    }
    Serial.println("");
  }
#endif
}

void report(byte row, byte col, boolean value)
{
#ifdef DEBUG_SERIAL
  Serial.print("Detected a change on ");
  Serial.print(col);
  Serial.print(" ");
  Serial.print(row);
  Serial.print(" to ");
  Serial.print(value);
  Serial.println(".");
#endif
}

//
// Key Reports
//

void release_keys_not_being_pressed()
{
  // we use charsReportedLastTime to figure out what we might
  // not be holding anymore and can now release. this is
  // destructive to charsReportedLastTime

  for (byte i = 0; i < KEYS_HELD_BUFFER; i++) {
    // for each key we were holding as of the end of the last cycle
    // see if we're still holding it
    // if we're not, call an explicit Release

    if (charsReportedLastTime[i] != 0x00) {
      // if there _was_ a character in this slot, go check the
      // currently held characters
      for (byte j = 0; j < KEYS_HELD_BUFFER; j++) {
        if (charsReportedLastTime[i] == charsBeingReported[j]) {
          // if's still held, we don't need to do anything.
          charsReportedLastTime[i] = 0x00;
          break;
        }
      }
      Keyboard.release(charsReportedLastTime[i]);

    }
  }
}

void record_key_being_pressed(byte character)
{
  for (byte i = 0; i < KEYS_HELD_BUFFER; i++) {
    // todo - deal with overflowing the 12 key buffer here
    if (charsBeingReported[i] == 0x00) {
      charsBeingReported[i] = character;
      break;
    }
  }
}

void reset_key_report()
{
  memcpy( charsReportedLastTime, charsBeingReported, KEYS_HELD_BUFFER);
  memset(charsBeingReported, 0, KEYS_HELD_BUFFER);

}


// Sending events to the usb host

void handle_synthetic_key_press(byte switchState, Key mappedKey) {
  if (mappedKey.flags & IS_CONSUMER) {
    if (key_toggled_on (switchState)) {
      Keyboard.consumerControl(mappedKey.rawKey);
    }
  }
  else if (mappedKey.flags & IS_SYSCTL) {
    if (key_toggled_on (switchState)) {
      Keyboard.systemControl(mappedKey.rawKey);
    }
  }
  else  if (mappedKey.flags & IS_MACRO) {
    if (key_toggled_on (switchState)) {
      if (mappedKey.rawKey == 1) {
        Serial.print("Keyboard.IO keyboard driver v0.00");
      }
    }
  } else if (mappedKey.rawKey == KEY_MOUSE_BTN_L
             || mappedKey.rawKey == KEY_MOUSE_BTN_M
             || mappedKey.rawKey == KEY_MOUSE_BTN_R) {
    if (key_toggled_on (switchState)) {
      Mouse.press(mappedKey.rawKey);
      end_warping();
    } else if (key_is_pressed(switchState)) {
    } else if (Mouse.isPressed(mappedKey.rawKey) ) {
      Mouse.release(mappedKey.rawKey);
    }
  }
}

void send_key_event(byte row, byte col)
{
  //for every newly pressed button, figure out what logical key it is and send a key down event
  // for every newly released button, figure out what logical key it is and send a key up event


  // TODO:switch to sending raw HID packets

  // really, these are signed small ints

  byte switchState = matrixState[row][col];
  Key mappedKey = keymaps[active_keymap][row][col];

  if (mappedKey.flags & MOUSE_KEY ) {
    if (mappedKey.rawKey & MOUSE_WARP) {
      if (key_toggled_on(switchState)) {
        warp_mouse(mappedKey);
      }
    } else {
      handle_mouse_key_press(switchState, mappedKey, x, y);
    }

  } else if (mappedKey.flags & SYNTHETIC_KEY) {
    handle_synthetic_key_press(switchState, mappedKey);
  }
  else {
    if (String("Slack") == myApp) {
      if (key_is_pressed(switchState)) {
        record_key_being_pressed(mappedKey.rawKey);
        if (key_toggled_on (switchState)) {
          Keyboard.print("Never gonna give you up!");
        }
      }
    } else {
      if (key_is_pressed(switchState)) {
        record_key_being_pressed(mappedKey.rawKey);
        if (key_toggled_on (switchState)) {
          press_key(mappedKey);
        }
      } else if (key_toggled_off (switchState)) {
        release_key(mappedKey);
      }

    }
  }
}

void press_key(Key mappedKey) {
  Keyboard.press(mappedKey.rawKey);
  if (commandBufferSize >= 31) {
    commandBufferSize = 0;
  }
  commandBuffer[commandBufferSize++] = mappedKey.rawKey;


  if ( mappedKey.rawKey == KEY_ENTER  ||
       mappedKey.rawKey == KEY_RETURN ) {
    commandPromptPrinted = false;
    process_command_buffer();
    commandBufferSize = 0;
  }
}

void release_key(Key mappedKey) {
  Keyboard.release(mappedKey.rawKey);
}



void make_input(sx1509Class sx1509, int pin) {
  sx1509.pinDir(pin, INPUT);  // Set SX1509 pin 1 as an input
  sx1509.writePin(pin, HIGH);  // Activate pull-up


}

void make_output(sx1509Class sx1509, int pin) {
  sx1509.pinDir(pin, OUTPUT);
  sx1509.writePin(pin, HIGH);

}


void setup_pins() {
  right_initted = setup_sx1509(rightsx1509, right_colpins, right_rowpins);
  left_initted = setup_sx1509(leftsx1509, left_colpins, left_rowpins);

}


int setup_sx1509 (sx1509Class sx1509, int colpins[], int rowpins[]) {
  byte initted;

  for (int counter = 0; counter < 10; counter++) {
    initted = sx1509.init();

    if (initted)
      break;
  }

  if (initted) { // init ok
    // In order to use the keypad, the clock must first be
    // configured. We can call configureClock() with the default
    // parameters (2MHz internal oscillator, no clock in/out).
    sx1509.configClock();



    // the debounceConfig function sets the debounce time. This
    //  function's parameter should be a 3-bit value.
    // 0: 0.5ms * 2MHz/fOSC
    // 1: 1ms * 2MHz/fOSC
    // 2: 2ms * 2MHz/fOSC
    // 3: 4ms * 2MHz/fOSC
    // 4: 8ms * 2MHz/fOSC
    // 5: 16ms * 2MHz/fOSC
    // 6: 32ms * 2MHz/fOSC
    // 7: 64ms * 2MHz/fOSC
    sx1509.debounceConfig(4);  // maximum debuonce time


    for (int i = 0; i < LEFT_ROWS; i++) {
      make_output(sx1509, rowpins[i]);
    }

    for (int j = 0; j < LEFT_COLS; j++) {
      make_input(sx1509, colpins[j]);
      sx1509.debounceEnable(colpins[j]);
    }


  }
  return initted;

}