Tatsuhiko Miyagawa
1e36ab17a6
|
2 years ago | |
|---|---|---|
| .. | ||
| src | 3 years ago | |
| README.md | 2 years ago | |
| library.properties | 4 years ago | |
README.md
MouseKeys
Have you ever wanted to control the mouse cursor from the comfort of your keyboard? With this plugin, you can. While it may not replace the mouse in all situations, there are plenty of cases where one will not have to lift their hands off the keyboard just to nudge the mouse cursor away a little.
Of course, there are a lot more one can do with the plugin than to nudge the cursor! Mouse keys are provided for all four and diagonal movement; mouse buttons; and a unique warping mechanism too. And not only these: the speed of the cursor, the mouse wheel, and that of acceleration can all be configured to match one's desired behaviour.
Using the plugin
To use the plugin, simply include the header in your Sketch, tell the firmware
to use the MouseKeys object, and place mouse keys on your keymap. It is best
illustrated with an example:
#include <Kaleidoscope.h>
#include <Kaleidoscope-MouseKeys.h>
// Somewhere in the keymap:
Key_mouseUp, Key_mouseDn, Key_mouseL, Key_mouseR,
Key_mouseBtnL, Key_mouseBtnR
KALEIDOSCOPE_INIT_PLUGINS(MouseKeys);
void setup() {
Kaleidoscope.setup ();
}
Keys provided by the plugin
The plugin provides a number of keys one can put on the keymap, that allow control of the mouse. They can be divided into a few groups:
Cursor movement
The simplest set of keys are the mouse cursor movement keys. These move the
cursor one direction or the other, with speed and acceleration factored in. When
a mouse cursor movement key is held down, it will move .speed pixels each
.speedDelay milliseconds without acceleration. But when .accelSpeed is
non-zero (and it is not zero by default,
see below), the speed will increase by
.accelSpeed every .accelDelay milliseconds. Thus, unless configured
otherwise, holding a direction will move that way at increasing speed.
One can hold more than one key down at the same time, and the cursor will move towards a direction that is the combination of the keys held. For example, holding the "mouse up" and "mouse right" keys together will move the cursor diagonally up and right.
The cursor movement keys are as follows:
Key_mouseUp,Key_mouseDn,Key_mouseL,Key_mouseR: Move the cursor up, down, left, or right, respectively.Key_mouseUpL,Key_mouseUpR,Key_mouseDnL,Key_mouseDnR: Move the cursor up-left, up-right, down-left, down-right, respectively.
Scroll wheel
Controlling the scroll wheel is similarly simple. It does not have acceleration,
but one can control the speed with the .wheelSpeed and .wheelDelay
properties (see below).
Key_mouseScrollUp,Key_mouseScrollDn: Scroll the mouse wheel up or down, respectively.Key_mouseScrollL,Key_mouseScrollR: Scroll the mouse wheel left or right, respectively.
Buttons
Buttons are even simpler than movement: there is no movement speed, nor acceleration involved. One just presses them.
Key_mouseBtnL,Key_mouseBtnM,Key_mouseBtnR,Key_mouseBtnP,Key_mouseBtnN: The left, middle, right, previous, and next mouse buttons, respectively.
Warping
Warping is one of the most interesting features of the plugin, and is a feature unique to Kaleidoscope, as far as we can tell. The warping keys position the mouse cursor within a sector of the screen on first press, and any subsequent taps will warp within the previously selected sector. For example, pressing the north-west warp key twice will first jump to the middle of the north-west sector of your screen, then select the north-west sector of that, and jump to the middle of it.
To stop warping, use any other mouse key, or hit the "warp end" key.
Warp grid size
The warp grid size determines how MouseKeys partitions the screen to select the next position to jump to when pressing a warp key. The plugin provides two grid sizes to choose from: a 2x2 grid that splits the screen into quadrants, and a 3x3 grid with nine cells similar to a navigation feature included with some speech recognition software. By default, the plugin splits the screen into the 2x2 grid.
To change the warp grid size, call the plugin's setWarpGridSize() method:
MouseKeys.setWarpGridSize(MOUSE_WARP_GRID_3X3);
2x2 grid
As described above, MouseKeys warps the pointer using a grid model that reflects locations on the screen. By default, the plugin uses a 2x2 grid. To understand how warping works, examine this diagram of a screen split into that 2x2 grid:
+-----------------------|-----------------------+
| | | |
| G | tab | |
| | | |
|-----------|-----------| tab |
| | | |
| B | esc | |
| | | |
+-----------------------|-----------------------+
| | |
| | |
| | |
| B | esc |
| | |
| | |
| | |
+-----------------------|-----------------------+
Each quadrant is labed with a key that, when pressed, moves the mouse pointer to the center of that quadrant. With this layout, pressing G warps the pointer to the top-left quadant. Then, the plugin "zooms" into that sector with a smaller grid so that the next warp key pressed jumps the pointer more precisely within the sector. In this case, if we press esc next, the pointer warps to the bottom-right corner within that quadrant.
The warping keys for the 2x2 grid are the following:
Key_mouseWarpNW,Key_mouseWarpNE,Key_mouseWarpSW,Key_mouseWarpSE: Warp towards the north-west, north-east, south-west, or south-east quadrants, respectively.Key_mouseWarpEnd: End the warping sequence, resetting it to the default state. Using any of the warping keys after this will start from the whole screen again.
3x3 grid
A 3x3 warp grid assigns a key to each of nine sectors of the screen. The next diagram shows a screen with a key label that warps to each sector. As we can see, pressing W warps the pointer into the top-left sector, and pressing V warps to the bottom-right corner within that sector:
+-----------------|-----------------|-----------------+
| W | E | R | | |
|-----|-----|-----| | |
| S | D | F | E | R |
|-----|-----|-----| | |
| X | C | V | | |
+-----------------|-----------------|-----------------+
| | | |
| | | |
| S | D | F |
| | | |
| | | |
+-----------------|-----------------|-----------------+
| | | |
| | | |
| X | C | V |
| | | |
| | | |
+-----------------|-----------------|-----------------+
To use a 3x3 warp grid, we may need to remap some keys. A suggested warp key mapping is shown below on the left side of a keyboard with a QWERTY layout:
W | E | R T A - End Warping (Key_mouseWarpEnd)
---|---|--- W - Warp NW Sector (Key_mouseWarpNW)
A S | D | F G E - Warp N Sector (Key_mouseWarpN)
---|---|--- R - Warp NE Sector (Key_mouseWarpNE)
X | C | V B S - Warp W Sector (Key_mouseWarpW)
D - Warp/Zoom Center (Key_mouseWarpIn)
F - Warp E Sector (Key_mouseWarpE)
X - Warp SW Sector (Key_mouseWarpSW)
C - Warp S Sector (Key_mouseWarpS)
V - Warp SE Sector (Key_mouseWarpSE)
T - Right Click (Key_mouseBtnR)
G - Left Click (Key_mouseBtnL)
B - Middle Click (Key_mouseBtnM)
This example layout replaces the default directional mouse keys and sets the warp keys in a comfortable position for a warp-only configuration. Of course, a Kaleidoscope user may retain the directional keys and map the warp keys elsewhere according to his or her liking.
A 3x3 warp grid layout contains all of the keys from the 2x2 grid layout with the following additions:
Key_mouseWarpN,Key_mouseWarpE,Key_mouseWarpS,Key_mouseWarpW: Warp towards the north, east, south, and west sectors, respectively.Key_mouseWarpIn: Warp to the center sector of the grid. The plugin will continue to "zoom" into center of the current cell with each consecutive press of this key.
Plugin methods
The plugin provides a MouseKeys object, with the following methods and
properties available:
.speed and .speedDelay
These two control the speed of the mouse cursor, when a movement key is held. The former,
.speed, controls the amount of pixels the cursor moves, when it has to move, and defaults to 1. The latter,.speedDelayis the amount of time - in milliseconds - to wait between two movements, and defaults to 0, no delay.
.accelSpeed and .accelDelay
These two properties control the speed of acceleration. The former,
.accelSpeed, controls how much the speed shall be increased at each step, while the second,.accelDelay, controls how often (in milliseconds) acceleration should be applied.They default to 1 pixel and 50 milliseconds, respectively.
.wheelSpeed and .wheelDelay
The last two properties supported by the plugin control the mouse wheel scrolling speed. The former,
.wheelSpeed, controls the amount of ticks the wheel shall scroll, and defaults to 1. The second,.wheelDelay, controls the delay between two scroll events, and defaults to 50 milliseconds.
.setSpeedLimit
This method sets the maximum speed after which acceleration stops. The default is 127, and the minimum value is 16 (things will not work properly below 16).
.setWarpGridSize
This method changes the size of the grid used for warping. The following are valid sizes:
MOUSE_WARP_GRID_2X2,MOUSE_WARP_GRID_3X3
Further reading
There is an example that demonstrates how to use this plugin.