You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
Kaleidoscope/plugins/Kaleidoscope-MouseKeys
Michael Richters a0045f4d9e
End mouse warping when any non-warp mouse key toggles on
2 years ago
..
src End mouse warping when any non-warp mouse key toggles on 2 years ago
README.md Rewrite MouseKeys plugin 2 years ago
library.properties More library tweaking to comply with arduino requirements 4 years ago

README.md

MouseKeys

Have you ever wanted to control the mouse cursor from the comfort of your keyboard? With this plugin, you can. While it may not replace the mouse in all situations, there are plenty of cases where one will not have to lift their hands off the keyboard just to nudge the mouse cursor away a little.

Of course, there are a lot more one can do with the plugin than to nudge the cursor! Mouse keys are provided for all four and diagonal movement; mouse buttons; and a unique warping mechanism too. And not only these: the speed of the cursor, the mouse wheel, and that of acceleration can all be configured to match one's desired behaviour.

Using the plugin

To use the plugin, simply include the header in your Sketch, tell the firmware to use the MouseKeys object, and place mouse keys on your keymap. It is best illustrated with an example:

#include <Kaleidoscope.h>
#include <Kaleidoscope-MouseKeys.h>

// Somewhere in the keymap:
Key_mouseUp, Key_mouseDn, Key_mouseL, Key_mouseR,
Key_mouseBtnL, Key_mouseBtnR

KALEIDOSCOPE_INIT_PLUGINS(MouseKeys);

void setup() {
  Kaleidoscope.setup ();
}

Keys provided by the plugin

The plugin provides a number of keys one can put on the keymap, that allow control of the mouse. They can be divided into a few groups:

Mouse buttons

Mouse button keys are straightforward; pressing one is the same as pressing the corresponding button on a physical mouse. You can hold a mouse button key to perform drag gestures, as you might expect. MouseKeys supports five mouse buttons: left, right, middle, previous, and next.

  • Key_mouseBtnL, Key_mouseBtnM, Key_mouseBtnR, Key_mouseBtnP, Key_mouseBtnN: The left, middle, right, previous, and next mouse buttons, respectively.

Cursor movement

When a cursor movement key is pressed, the mouse cursor will begin to move slowly, then accelerate to full speed. Both the full speed and the time it takes to reach full speed are configurable.

The cursor movement keys are as follows:

  • Key_mouseUp, Key_mouseDn, Key_mouseL, Key_mouseR: Move the cursor up, down, left, or right, respectively.
  • Key_mouseUpL, Key_mouseUpR, Key_mouseDnL, Key_mouseDnR: Move the cursor up-left, up-right, down-left, down-right, respectively.

Scroll wheels

Controlling the scroll wheel is similarly simple. It does not have acceleration, but one can control the speed with the MouseKeys.setScrollInterval() function, which controls the length of time between scroll events.

  • Key_mouseScrollUp, Key_mouseScrollDn: Scroll the mouse wheel up or down, respectively.
  • Key_mouseScrollL, Key_mouseScrollR: Scroll the mouse wheel left or right, respectively.

Warping

Warping is one of the most interesting features of the plugin, and is a feature unique to Kaleidoscope, as far as we can tell. The warping keys position the mouse cursor within a sector of the screen on first press, and any subsequent taps will warp within the previously selected sector. For example, pressing the north-west warp key twice will first jump to the middle of the north-west sector of your screen, then select the north-west sector of that, and jump to the middle of it.

To stop warping, use any other mouse key, or hit the "warp end" key.

Warp grid size

The warp grid size determines how MouseKeys partitions the screen to select the next position to jump to when pressing a warp key. The plugin provides two grid sizes to choose from: a 2x2 grid that splits the screen into quadrants, and a 3x3 grid with nine cells similar to a navigation feature included with some speech recognition software. By default, the plugin splits the screen into the 2x2 grid.

To change the warp grid size, call the plugin's setWarpGridSize() method:

MouseKeys.setWarpGridSize(MOUSE_WARP_GRID_3X3);

2x2 grid

As described above, MouseKeys warps the pointer using a grid model that reflects locations on the screen. By default, the plugin uses a 2x2 grid. To understand how warping works, examine this diagram of a screen split into that 2x2 grid:

+-----------------------|-----------------------+
|           |           |                       |
|     G     |    tab    |                       |
|           |           |                       |
|-----------|-----------|          tab          |
|           |           |                       |
|     B     |    esc    |                       |
|           |           |                       |
+-----------------------|-----------------------+
|                       |                       |
|                       |                       |
|                       |                       |
|           B           |          esc          |
|                       |                       |
|                       |                       |
|                       |                       |
+-----------------------|-----------------------+

Each quadrant is labed with a key that, when pressed, moves the mouse pointer to the center of that quadrant. With this layout, pressing G warps the pointer to the top-left quadant. Then, the plugin "zooms" into that sector with a smaller grid so that the next warp key pressed jumps the pointer more precisely within the sector. In this case, if we press esc next, the pointer warps to the bottom-right corner within that quadrant.

The warping keys for the 2x2 grid are the following:

  • Key_mouseWarpNW, Key_mouseWarpNE, Key_mouseWarpSW, Key_mouseWarpSE: Warp towards the north-west, north-east, south-west, or south-east quadrants, respectively.
  • Key_mouseWarpEnd: End the warping sequence, resetting it to the default state. Using any of the warping keys after this will start from the whole screen again.

3x3 grid

A 3x3 warp grid assigns a key to each of nine sectors of the screen. The next diagram shows a screen with a key label that warps to each sector. As we can see, pressing W warps the pointer into the top-left sector, and pressing V warps to the bottom-right corner within that sector:

+-----------------|-----------------|-----------------+
|  W  |  E  |  R  |                 |                 |
|-----|-----|-----|                 |                 |
|  S  |  D  |  F  |        E        |        R        |
|-----|-----|-----|                 |                 |
|  X  |  C  |  V  |                 |                 |
+-----------------|-----------------|-----------------+
|                 |                 |                 |
|                 |                 |                 |
|        S        |        D        |        F        |
|                 |                 |                 |
|                 |                 |                 |
+-----------------|-----------------|-----------------+
|                 |                 |                 |
|                 |                 |                 |
|        X        |        C        |        V        |
|                 |                 |                 |
|                 |                 |                 |
+-----------------|-----------------|-----------------+

To use a 3x3 warp grid, we may need to remap some keys. A suggested warp key mapping is shown below on the left side of a keyboard with a QWERTY layout:

   W | E | R  T      A - End Warping      (Key_mouseWarpEnd)
  ---|---|---        W - Warp NW Sector   (Key_mouseWarpNW)
A  S | D | F  G      E - Warp N Sector    (Key_mouseWarpN)
  ---|---|---        R - Warp NE Sector   (Key_mouseWarpNE)
   X | C | V  B      S - Warp W Sector    (Key_mouseWarpW)
                     D - Warp/Zoom Center (Key_mouseWarpIn)
                     F - Warp E Sector    (Key_mouseWarpE)
                     X - Warp SW Sector   (Key_mouseWarpSW)
                     C - Warp S Sector    (Key_mouseWarpS)
                     V - Warp SE Sector   (Key_mouseWarpSE)
                     T - Right Click      (Key_mouseBtnR)
                     G - Left Click       (Key_mouseBtnL)
                     B - Middle Click     (Key_mouseBtnM)

This example layout replaces the default directional mouse keys and sets the warp keys in a comfortable position for a warp-only configuration. Of course, a Kaleidoscope user may retain the directional keys and map the warp keys elsewhere according to his or her liking.

A 3x3 warp grid layout contains all of the keys from the 2x2 grid layout with the following additions:

  • Key_mouseWarpN, Key_mouseWarpE, Key_mouseWarpS, Key_mouseWarpW: Warp towards the north, east, south, and west sectors, respectively.
  • Key_mouseWarpIn: Warp to the center sector of the grid. The plugin will continue to "zoom" into center of the current cell with each consecutive press of this key.

Plugin methods

The plugin provides a MouseKeys object, with the following methods and properties available:

.setCursorInitSpeed(speed)/.getCursorInitSpeed()

Controls (or returns) the current starting speed value for mouse cursor movement. When a mouse movement key is pressed, the cursor starts moving at this speed, then accelerates. The number is abstract, but linear, with higher numbers representing faster speeds. Default starting speed is 1.

.setCursorBaseSpeed(speed)/.getCursorBaseSpeed()

Controls (or returns) the current top speed value for mouse cursor movement. When a mouse movement key is pressed, the cursor accelerates until it reaches this speed. The number is abstract, but linear, with higher numbers representing faster speeds. Default full-speed value is 50.

.setCursorAccelDuration(duration)/.getCursorAccelDuration()

Controls (or returns) the current time it takes for the mouse cursor to reach full speed (in milliseconds), starting from when the first movement key is pressed. Default value is 800 ms.

.setScrollInterval(interval)/.getScrollInterval()

Controls (or returns) the current scrolling speed, by setting the time between mouse scroll reports (in milliseconds). Default value is 50 ms.

.setWarpGridSize(size)

This method changes the size of the grid used for warping. The following are valid sizes: MOUSE_WARP_GRID_2X2, MOUSE_WARP_GRID_3X3

Further reading

There is an example that demonstrates how to use this plugin.