This removes the `magic` field from the beginning of the header. It was
originally meant to signal if the EEPROM we're dealing with is new, or if it has
been set up with `EEPROMSettings` before. But as `EEPROMSettings` is pretty much
the only way we deal with EEPROM, there's not much need for that.
With the removal, we do need a way to update the CRC bits on first use, so we
use the `version` field instead: if it is `0xff`, we update the CRC, and
consider the settings valid. This means that until the version is set, the
EEPROM layout is considered flexible, and verification is essentially disabled.
Once the version is set, we can validate.
Signed-off-by: Gergely Nagy <algernon@keyboard.io>
While there, drop the `keymap.layer` command, which was a workaround to a
Chrysalis bug fixed since.
Signed-off-by: Gergely Nagy <algernon@keyboard.io>
This is not directly used by Kaleidoscope itself, but we provide the hook from
here, for the sake of convenience. It will be used by plugins such as
`Kaleidoscope-FocusSerial`, in much the same way as Focus hooks were used
previously.
This does change the architecture a bit, and the `FOCUS_HOOK_KALEIDOSCOPE` focus
hook previously provided by Kaleidoscope itself is something that no longer
belongs to core, but rather to a plugin. As such, the hook is removed as part of
this patch.
Signed-off-by: Gergely Nagy <algernon@keyboard.io>
`max_layers` is a method, so comparing to that would be integer<->pointer
comparison. We want to compare to `max_layers_`.
Signed-off-by: Gergely Nagy <algernon@keyboard.io>
If we're looking up a key from `PROGMEM`, only do that if the layer in question
is smaller than `layer_count`. Doing otherwise would read garbage from `PROGMEM`
in case we try to read from a layer higher than what we have in there. This can
happen if we have more layers in `EEPROM` than in `PROGMEM`.
Signed-off-by: Gergely Nagy <algernon@keyboard.io>
To make it easier to use the plugin, pull in `EEPROMSettings` by default, and
explicitly call its `onSetup` (it is safe to do so), so user sketches don't have
to if they don't use `EEPROMSettings` directly. Also set `Layer.getKey` to
`EEPROMKeymap.getKeyOverride` to provide a sensible default.
Signed-off-by: Gergely Nagy <algernon@keyboard.io>
If `EEPROMSettings.seal()` wasn't explicitly called, seal the layout in
`beforeEachCycle()`. On the flip side, this makes user sketches simpler, because
they don't have to seal explicitly. This is done at the cost of an if check each
cycle.
In the long run, EEPROM layout management will be moving out of this plugin, so
this check will be eventually dropped too.
Signed-off-by: Gergely Nagy <algernon@keyboard.io>
These two lines went in by mistake earlier, they were meant for local
debugging only. As such, having them in the plugin is a bug, easily
squashed by removing them.
Signed-off-by: Csilla Nagyné Martinák <csilla@csillger.hu>
With keyboardio/Kaleidoscope-Build-Tools#2, it is now done by the `travis-test`
target. We still need to install the shellcheck package, however.
Fixes#356.
Signed-off-by: Gergely Nagy <algernon@keyboard.io>
With the Atreus, we have a board that has a different max upload size depending
on what MCU is used. Until we figure out how to properly support that in the CLI
builder, default to using the first value. That's a reasonable approximation in
most cases.
Signed-off-by: Gergely Nagy <algernon@keyboard.io>
Jesse Vincent
Gergely Nagy
Jesse Vincent
Gergely Nagy
Csilla Nagyné Martinák