The plugin.h header only defined the KaleidoscopePlugin class, and while
there was a reason it was separate from Kaleidoscope.h, that reason is
long gone. Merge it there, and remove any reference to plugin.h, as it
is not needed anymore.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Since we pre-fill the cached `keyMap` with the value of `DefaultLayer`, there is
no need to check that layer again, looking for a non-transparent key. Whatever
is there, will be used anyway.
This way we save a cycle for keys that are transparent everywhere but the
default layer.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
We fill the cached `keyMap` with the value of `DefaultLayer`, so if that is the
only layer active, then we can bail out early.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of going through all the active layers each time we are looking for a
key, whenever we switch layers, compute the effective keymap, and store the
indexes. This makes the lookup a considerably faster operation, and lookups
happen far more often than layer switching.
This comes at a cost of ROWS*COLS amount of memory, and a bit of code, but on
the flip side, the lookup operation is now O(1), which is a very nice property
to have, if you want responsiveness. Changing layers is marginally slower,
however, but even with 32 active layers, doing the computation once, instead of
potentially many dozens of time, is still worth it.
We could further reduce the memory requirements if we stored more columns per
byte, but that's for a future optimization.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Renamed the library to Kaleidoscope-LEDEffect-SolidColor, and followed up with
other renames.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Not all keyboard hardware has per-key LEDs, and not all of them define the LED_*
helpers. To make the LEDControl at least compile for these, guard the
BootAnimation with a Model01-specific ifdef.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
The build-all command needs a clean(-ish) slate, and must re-set the build-dir,
otherwise a successful build of a previous plugin will remove it. As a
workaround, re-launch the builder in this case.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of counting loops for the purpose of calculating acceleration, use
timers and steps instead. This means that we can now tune how often the mouse
moves (`speedDelay`), how much it moves when it does (`speed`), how fast
acceleration is (`accelSpeed`), and how often we accelerate (`accelDelay`).
By default, the movement speed is one, and there is no delay, while acceleration
has an 50ms delay, and a speed of one.
But all of these can be tuned at run-time: we can turn off acceleration
completely, or slow down the mouse considerably - the possibilities are almost
endless!
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
With the recent speedup of the scan cycle, we need some delays for the animation
to look nice.
Fixes#2.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of always iterating through all layers, which slows us down
considerably, keep track of the highest active one, and start from there.
This has a VERY noticeable impact on the speed at which we finish a scan cycle.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Momentary layer switchers were broken, because they had the flags/keyCode parts
swapped. Apparently, I missed these when swapping the rest.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Gergely Nagy
Jesse Vincent
Jesse Vincent