We want to allow plugins to change how keys are looked up - or where they are
looked up from -, and for this, the way we do that final lookup from `keymaps`
or elsewhere, must be overrideable.
We do this by having a `getKey` function pointer in the `Layer_` class, which
defaults to `getKeyFromPROGMEM`. Any plugin, or sketch, can change where
`getKey` points to, and thereby change the way keys are looked up.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
If we want to allow plugins to implement EEPROM storage, it is best if we don't
do anything with EEPROM in the core firmware. As such, remove the
`Layer.defaultLayer` call from `Kaleidoscope.setup`.
With that gone, the `keymap_count` argument is obsolete, so drop it from
`Kaleidoscope.setup()` - but we keep an temporary `setup()` with the old arity,
so that plugins can be updated at a slower pace.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Drop the `load_primary_layer` and `save_primary_layer` methods, because
`save_primary_layer` is not used anywhere, and as such, the whole thing is
pointless at this time.
Furthermore, if we want to allow plugins to implement EEPROM storage, then its
best if we leave the default layer save/load to the plugins too.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
To further improve the LED performance, sync only when there is a change. We do
this by tracking when change happens, assuming everyone uses the provided
accessors.
While we do a bit of extra work each cycle to do the tracking, that pales in
comparison to what we gain by not having to transfer data needlessly.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of calculating a time delta every time we want to check for a
timeout, compute the projected end ahead of time.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of calculating time deltas every time we want to check a
timeout, calculate the projected end ahead of time.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of calculating the time delta each time we want to check for a
timeout, calculate the projected ending time ahead of time.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of calculating the time delta each time we check for a timeout,
pre-calculate the projected ending time, and compare against that.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of calculating the time delta every time we want to check if the
timer elapsed, calculate the projected ending time at the start, and
compare against that.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of calculating the elapsed time every time we check the timer,
calculate the projected end-time when we start the timer, and just
compare millis() against that.
Also removes the `.configure()` method, in favour of making the
`timeOut` property public.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Instead of doing a substraction and a compare in the if check, whenever we reset
the timer, add `syncDelay`, and compare against the timer only. Should result in
marginally better performing code.
Thanks @obra for the suggestion!
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Because `led_sync` is a major cause of slowness, do not sync every cycle. In
most cases, it is pointless to sync 100 times a second, about 60 - or even 30 -
may be more than enough.
For this reason, introduce a timer, and a settable delay: we'll only call
`led_sync` once the delay's up. It can be set to 0 to call it every time, but
defaults to 16 (for about 62 syncs/sec), as a safe bet.
This speeds the loop up dramatically, except for the few exceptions where sync
is called.
Fixes#1.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
The `CRGB` macro takes rgb values as arguments, in this order, and creates a
`cRGB` instance with the components rearranged to fit the ordering of the
hardware (in the case of the Model01, bgr).
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
The `USE_PLUGINS()` macro is a clever hack, to make it seem like
`Kaleidoscope.use()` is type-safe. It pushes its arguments into an appropriately
typed array, so anything that does not fit the criteria, will trigger a compiler
error.
It then never uses the array, and passes the plugins over to
`Kaleidoscope.use`, adding the trailing `NULL`, making it even easier to
use.
Since the array this macro creates is never used, the compiler will
optimize it out fully. As such, by using this macro, we incur neither
any size penalties, nor any run-time penalties. Everything happens at
compile-time.
Fixes#100.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Do not store the previous layer state, and instead of updating only when
the layer changes, just update anyway. It's not that costy anymore, with
the recent `Layer.lookup` optimisations.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
To make things easier, just include the main header. It includes
everything else we need, and this way we do not need to cherry pick, nor
care if any of the other headers move, disappear, etc.
Signed-off-by: Gergely Nagy <algernon@madhouse-project.org>
Gergely Nagy
Jesse Vincent
Jesse Vincent