Intended to force-reactivate the current LED mode, in case we want to refresh
the whole board, and make sure we do so even if the current mode's update is a
no-op.
This can happen when we overrode some keys, and it becomes less costly to update
everything than to iterate over the updated keys.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
When implementing `.refreshAt` before, some dead code was left in
Kaleidoscope-LEDControl.cpp, code that is now implemented in the header.
As these are implemented elsewhere, and are `#if 0`'d out anyway, drop them.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
* Added Arduino IDE install instructions
Completed a first draft of the IDE install instructions through flashing the board with the unedited sketch.
Also made a couple edits as suggested by @algernon, and a few other refinements I noticed.
* typo
Wanted to post this in the partial state so folks can start reviewing what I've done and making suggestions. This is a first draft of the intro section, and the outline for the rest of the document.
Make `Kaleidoscope_` a friend class, so that it can access `.begin`. The reason
behind this is that `.begin` is an interface towards `Kaleidoscope.use()`, and
that function should be the only user. To discourage its use, make it protected.
This does not break any existing - and valid - code, but allows us to slowly
migrate the plugins to a protected `begin()` method.
Fixes#177.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
`Kaleidoscope.use` is a much better interface, therefore deprecate USE_PLUGINS.
We do this by creating a wrapper function, `__USE_PLUGINS` that will call
`Kaleidoscope.use` under the hood, but has a deprecated attribute attached. We
then make the `USE_PLUGINS` macro call this function.
We do this because we want to make sure that the list is NULL-terminated, and
for that, we need the macro.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
This was only ever used for `Kaleidoscope.setup()`, and while the variant that
takes an argument is deprecated, and emits a warning already, we can do the same
for `KEYMAP_SIZE` too.
This does set the const to 0, so if used anywhere else than
`Kaleidoscope.setup()`, it will have undesired side-effects. But as far as I
saw, it was never used elsewhere, thus, this change should be safe.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
We do not use `keymap_count` anymore, so deprecate this variant of the setup
function, with a message that also tells the user that `KEYMAP_SIZE` is
deprecated too.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
Turn `event_handler_hook_use` and `loop_hook_use` into real functions, so that
we can apply a `deprecated` attribute, which in turn will emit a compile-time
warning when either of these functions are used.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
Neither of these are used in any plugin, within Arduino-Boards or outside of it.
We keep the `_hook_use` aliases, because there are a few users of it outside of
Arduino-Boards.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
Use `LAYER_SHIFT_OFFSET` instead of `MOMENTARY_OFFSET`, which will start
emitting compile-time warnings now.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
As discussed in #190, and later on IRC, this renames ToggleLayer to
LockLayer (updating the documentation at the same time), and introduces
the UnlockLayer alias, for clarity.
MomentaryLayer also got a new name: ShiftToLayer, and new documentation
to go with it.
Signed-off-by: Csilla Nagyné Martinák <csilla@csillger.hu>
This introduces `ToggleLayer(n)` and `MomentaryLayer(n)`, which make it
easier to switch to layers higher than five, and allow one to use enum
values in place of `n`, such as: `ToggleLayer(NUMPAD)`,
`MomentaryLayer(FUNCTION)`.
Signed-off-by: Csilla Nagyné Martinák <csilla@csillger.hu>
Requiring the end-user to use a macro to have the NumLock effect is a bit
confusing. We can do better than that, by using an event handler hook, and
catching `Keypad_NumLock` presses, and toggle on keypress.
This way, the macro is not necessary, and all the user has to do, is to use the
plugin, configure `numPadLayer`, and done.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
Currently, if kaleidoscope-builder fails to find a sketch file, the
resulting error message is very confusing and unhelpful. This commit
makes it more straightforward and helpful.
Jesse Vincent
katee
Jesse Vincent
Gergely Nagy
Craig Disselkoen
Jennifer Leigh
Csilla Nagyné Martinák