Make Kaleidoscope_ a friend class, so that it can access .begin. The
reason behind this is that .begin is an interface towards
Kaleidoscope.use(), and that function should be the only user. To
discourage its use, make it protected.
This does not break any existing - and valid - code, but allows us to
slowly migrate the plugins to a protected begin() method.
Fixes#177.
I don't have write access, but through conversation with @Jennigma in the forum I've made a few changes above.
- I gave a first pass up to the Editing Keymaps part, then skimmed after there.
- I rearranged some sentences to try to fit more with the "voice" of the Keyboardio brand from its website, to the emails and tweets. It's a soft, friendly and inviting voice. Specifically I used a lot more "We", and tried to gracefully include lines like "uncompromising typists" and "heirloom-grade" (these distinctions left a powerful first impression on me). To be honest, I could spend A LOT more time doing that brand writing, it's so much fun. If there are parts that could be more "branded" let me know.
- I changed a few instances of "Keyboardio" to "Model 01", but perhaps not consistently, when I saw that "keyboardio" is lowercase in the Arduino board manager I wondered if I have over capitalized. If I thought a part of the software could apply to future Keyboardio-brand products I left it as "Keyboardio", and if it seemed very specific to this product I used "Model 01".
- I softened some parts, like removed the IDE part in the first paragraph, moving that to the Arduino introduction below.
- The only completely-removed line was about requiring cleverness and following instructions. I feel like those aren't required. The offers for support I've seen online suggest the non-clever would also get the help they need! Besides, the non-clever just use whatever flavour of rubber domes Dell is shipping this month amiright?! haha.
As discussed in #196, if we are making `KaleidoscopePlugin.begin` protected, we
might as well give it a better name. That name is `initialSetup`, and this
change is the first step towards the migration. It introduces `initialSetup`
which will call `begin` for now, and deprecate `begin`, which is no longer an
abstract function.
Once everyone migrated to the new name, we can remove `.begin`, and turn
`.initialSetup` into an abstract function.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
Intended to force-reactivate the current LED mode, in case we want to refresh
the whole board, and make sure we do so even if the current mode's update is a
no-op.
This can happen when we overrode some keys, and it becomes less costly to update
everything than to iterate over the updated keys.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
When implementing `.refreshAt` before, some dead code was left in
Kaleidoscope-LEDControl.cpp, code that is now implemented in the header.
As these are implemented elsewhere, and are `#if 0`'d out anyway, drop them.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
* Added Arduino IDE install instructions
Completed a first draft of the IDE install instructions through flashing the board with the unedited sketch.
Also made a couple edits as suggested by @algernon, and a few other refinements I noticed.
* typo
While we use milliseconds internally, the end-user will not need higher
precision than a second, therefore, store the settings with second-precision.
This is much friendlier towards the user, and also uses less space in EEPROM, by
about six bytes.
Addresses a part of #8, thanks @gedankenexperimenter!
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
Wanted to post this in the partial state so folks can start reviewing what I've done and making suggestions. This is a first draft of the intro section, and the outline for the rest of the document.
Make `Kaleidoscope_` a friend class, so that it can access `.begin`. The reason
behind this is that `.begin` is an interface towards `Kaleidoscope.use()`, and
that function should be the only user. To discourage its use, make it protected.
This does not break any existing - and valid - code, but allows us to slowly
migrate the plugins to a protected `begin()` method.
Fixes#177.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
`Kaleidoscope.use` is a much better interface, therefore deprecate USE_PLUGINS.
We do this by creating a wrapper function, `__USE_PLUGINS` that will call
`Kaleidoscope.use` under the hood, but has a deprecated attribute attached. We
then make the `USE_PLUGINS` macro call this function.
We do this because we want to make sure that the list is NULL-terminated, and
for that, we need the macro.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
This was only ever used for `Kaleidoscope.setup()`, and while the variant that
takes an argument is deprecated, and emits a warning already, we can do the same
for `KEYMAP_SIZE` too.
This does set the const to 0, so if used anywhere else than
`Kaleidoscope.setup()`, it will have undesired side-effects. But as far as I
saw, it was never used elsewhere, thus, this change should be safe.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
We do not use `keymap_count` anymore, so deprecate this variant of the setup
function, with a message that also tells the user that `KEYMAP_SIZE` is
deprecated too.
Signed-off-by: Gergely Nagy <kaleidoscope@gergo.csillger.hu>
James N. V. Cash
Gergely Nagy
Jesse Vincent
Gergely Nagy
Jesse Vincent
Jennifer Leigh
Craig Disselkoen
katee