Astyle

plugins/Kaleidoscope-Hardware-Keyboardio-Model100/src/kaleidoscope/device/keyboardio/Model100.cpp

@@ -54,12 +54,12 @@ void Model100Hands::setup(void) {
 // TODO   PORTE &= ~_BV(6);
 
 
-// Turn on the switched 5V network. 
-// TODO - make sure this happens at least 100ms after USB connect 
+// Turn on the switched 5V network.
+// TODO - make sure this happens at least 100ms after USB connect
 // to satisfy inrush limits
-pinMode(PC13, OUTPUT_OPEN_DRAIN);
-digitalWrite(PC13, LOW);
-Wire.begin();
+  pinMode(PC13, OUTPUT_OPEN_DRAIN);
+  digitalWrite(PC13, LOW);
+  Wire.begin();
   // Set B4, the overcurrent check to an input with an internal pull-up
 // TODO   DDRB &= ~_BV(4);	// set bit, input
 // TODO   PORTB &= ~_BV(4);	// set bit, enable pull-up resistor
@@ -109,7 +109,7 @@ cRGB Model100LEDDriver::getCrgbAt(uint8_t i) {
 
 void Model100LEDDriver::syncLeds() {
   if (!isLEDChanged)
-   return;
+    return;
   // LED Data is stored in four "banks" for each side
   // We send it all at once to make it look nicer.
   // We alternate left and right hands because otherwise

plugins/Kaleidoscope-Hardware-Keyboardio-Model100/src/kaleidoscope/driver/keyboardio/Model100Side.cpp

@@ -67,7 +67,7 @@ uint8_t Model100Side::controllerAddress() {
 // https://www.arduino.cc/en/Reference/WireEndTransmission
 byte Model100Side::setKeyscanInterval(byte delay) {
   uint8_t data[] = {TWI_CMD_KEYSCAN_INTERVAL, delay};
-  uint8_t result = writeData( data, ELEMENTS(data));
+  uint8_t result = writeData(data, ELEMENTS(data));
   return result;
 }
 
@@ -103,9 +103,9 @@ byte Model100Side::setLEDSPIFrequency(byte frequency) {
 }
 
 
-uint8_t Model100Side::writeData(uint8_t *data,uint8_t length) {
+uint8_t Model100Side::writeData(uint8_t *data, uint8_t length) {
   Wire.beginTransmission(addr);
-  Wire.write( data, length);
+  Wire.write(data, length);
   uint8_t result = Wire.endTransmission();
   return result;
 }
@@ -130,30 +130,30 @@ int Model100Side::readRegister(uint8_t cmd) {
 
   Wire.requestFrom(addr, 1);    // request 1 byte from the keyscanner
   if (Wire.available()) {
-	return Wire.read();
+    return Wire.read();
   } else {
-	return -1;
+    return -1;
   }
-  
+
 }
 
 
 // gives information on the key that was just pressed or released.
 bool Model100Side::readKeys() {
 
-   uint8_t row_counter = 0;
+  uint8_t row_counter = 0;
   // perform blocking read into buffer
   uint8_t read = 0;
   Wire.requestFrom(addr, 5);    // request 1 byte from the keyscanner
   if (Wire.available()) {
-	read = Wire.read();
-	if (TWI_REPLY_KEYDATA == read) {
-
-	while (Wire.available()) {
-		keyData.rows[row_counter++] = Wire.read();
-	}
-	return true;
-	}
+    read = Wire.read();
+    if (TWI_REPLY_KEYDATA == read) {
+
+      while (Wire.available()) {
+        keyData.rows[row_counter++] = Wire.read();
+      }
+      return true;
+    }
   }
   return false;
 }
@@ -180,9 +180,9 @@ void Model100Side::sendLEDBank(byte bank) {
      * that results in a considerably smoother curve. */
     uint8_t c = ledData.bytes[bank][i];
     if (c > brightness_adjustment_)
-     c -= brightness_adjustment_;
+      c -= brightness_adjustment_;
     else
-    c = 0;
+      c = 0;
 
     data[i + 1] = c;
   }
@@ -192,8 +192,8 @@ void Model100Side::sendLEDBank(byte bank) {
 void Model100Side::setAllLEDsTo(cRGB color) {
   uint8_t data[] = {TWI_CMD_LED_SET_ALL_TO,
                     color.b,
-		    color.g,
-	  	    color.r
+                    color.g,
+                    color.r
                    };
   uint8_t result  = writeData(data, ELEMENTS(data));
 }
@@ -202,8 +202,8 @@ void Model100Side::setOneLEDTo(byte led, cRGB color) {
   uint8_t data[] = {TWI_CMD_LED_SET_ONE_TO,
                     led,
                     color.b,
-		    color.g,
-	  	    color.r
+                    color.g,
+                    color.r
                    };
   uint8_t result  = writeData(data, ELEMENTS(data));
 

plugins/Kaleidoscope-MouseKeys/src/kaleidoscope/plugin/MouseKeys/MouseKeyDefs.h

@@ -82,4 +82,4 @@
 #define Key_mouseBtnN XXX
 
 
-#endif 
+#endif